Fred Dushin Ben Smith Dale Desprey Bill Maloney Bruce Fowler Dave Bobeck Dixon Kenner Alan Richer Mike Loidice
BBC Top 
Gear Land Rover vid 5mb Part of a series where people picked their 
favourite car for an 'all-time' greats poll. The Land Rover won hands 
  Vehicle Identification  
  History, Production, Sales 
  Repair & Maintenance
Data & Specifications
Chassis Numbers
Gearbox Renovation
Gearbox Removal
Unsticking a Stuck Clutch
Swivel Ball Repairs
Skirted Thermostats
Double Clutching
Clutch Operation Explained
Differential Offset
Series III Shift Lever Nylon Bushing Failure Repair
Rover VS Salisbury Differential
Body & Chassis
Perils Of Ownership
Forward Control
  Clubs & Parts Suppliers
What's New
  Contact Us
  Return to OVLR
  Return to Rover Web

Series Land Rovers

The Stuck Clutch

Here is some advice on freeing a stuck clutch . . . . remember to use those wading plugs!

There are two ways to free up a sticking clutch. Mine has stuck twice: once when the engine was sitting for a prolonged period on my garage floor with the clutch bolted on, and the other was just after having the flywheel machined (the virginal steel is *very* susceptible to rust then). It can also happen after the Rover was "ridden hard and put away wet" (i.e., no bell housing plug.)Point it in a safe direction and start the Rover in gear, working the clutch as you go. Choose successively higher gears until the lurching breaks it free...sounding for all the world like a snapping lay-shaft! :-0 (This is what Charlie Haig at RN does.) Took me to third one time to break it loose.

The other is to start your Rover in gear...chained to a tree! The weak link will part, and hopefully that is limited to the interface between clutch and flywheel. (This came from Mike McCaig who has used it successfully.)

Sandy Grice -

Looks like your clutch plate is rusted onto the flywheel; couldn't happen to me, always plenty of oil coming in through the rear crankshaft seal. That's what you get for having a 'dry' engine on a Rover, see?Anyway, to get it off: Take off the interior front housing of the gearbox ("gearbox diaphragm panel" is the proper denomination) to gain access to the upper part of the bell housing. There you will find a small metal plate the form of a lying capital "D" fixed by two screws. Take it off and you will find a hole giving access to the interior of the bell housing. Press the clutch pedal and spray some light, thin rust solvent oil into the housing, aiming high and well to the front of the clutch. Try not to smother the clutch too much. *Don't* use MO-oil, as this will ruin your clutch plate and give you plenty of 'shudder' later on. In the meantime put the car onto a straight and flat peace of road, preferably with a slight descent. After a few minutes, release the handbrake,put in 2nd gear *low ratio* and start the engine with the clutch released, i.e. don't have your foot on the clutch pedal. Someone pushing from behind would help. The starter will begin moving the car and start the engine at the same time. As soon an the engine is running, drive ahead at a moderate speed until the engines runs smooth. Now *press* the clutch all the way down and start playing with the throttle, making the car to jump and jerk (don't overdo it though!). The clutch should come loose with a loud *bang*. I must warn you that the clutch _might_ get damaged by this process, but if it does the gearbox will have to come off anyway. If it survives this treatment - and it usually does - you've saved yourself a lot of work. Afterwards, spray the inside of the bell housing (again through the little hole) liberally with brake cleaner to clear out as much of the rust solvent oil as possible. Reassemble.Just a short bit of advice for the next time you head into unknown murky depths,

  • plug the bottom opening of the bell housing with the appropriate screw before submersion (not forgetting to *un*plug it afterwards!), and/or
  • 'burn' the clutch plate dry afterwards by deliberately riding it for a while (again, not overdoing it).

Stefan R. Jacob <>
LROC of Hessen

Jack up the rear of the vehicle and put it on nice safe axle stands (ed. - Make DARNED sure it's secure and in 2WD), then select 2 wheel drive in 2nd or 3rd gear and start the engine. Now leave it on the axle stands rear wheels turning at about 20-30miles for 20 minutes whilst you go and have a cup of tea and let the whole thing warm up. When you get back jam on the brakes as hard as possible whilst depressing the clutch pedal and repeat a few times if necessary, with this safe and simple method having to take nothing apart or risk our lives on the road the clutch came free with just 3 attempts perfect....hope this helps anyone else with a similar problem.

Mark Downer

Mark has the right idea. Make sure the engine is good and HOT first! Start and in neutral with the brake on prop the throtle open to 1500rpm and let it run for close to a half hour. Once it is hot, shut it down and start in gear and drive in a SAFE place where you can get on and off the throttle while depressing the clutch. A steep hill helps a lot. A loud bang will signal success. Now slip the clutch a bit to clean off the rust from the flywheel and pressure plate.

Bill Maloney.



Copyright Dixon Kenner, 1995-2011. Last modified Feburary 25, 2009.
Comments? Send mail to Dixon Kenner or Benjamin Smith
Site Designed and Created by Bill Maloney
Russ Wison
Russ Dushin
Tom Tollefson
Steve Denis
Don Watson
Fixing It
Ted Rose's Buns
Andy Grafton